Роботы и компоненты к ним

который включает в себя основные компоненты и датчики. Вы можете создать много интересных проектов, даже если вы ничего не знаете о пайке. Это дела <<

фирмы Cypress - CY8C26443. Плата позволяет управлять 16-ю сервоприводами посредством интерфейса RS-232 и утилитой RoboRealm. <<

установлен чип ATmega32u4. Контроллер Arduino Leonardo на базе чипа Atmel ATmega32u4, на плате установлен микроконтроллер, который общается с компь <<

4 различных щита одновременно, при этом не конфликтующие между собой. Все это делает ваш проект компактным и функциональным. Применение:
- 3D печать
- <<

микроконтроллеров от Orion Robotics. Может управлять 2 двигателями постоянного тока до 3amps на канал. Также, включает в себя встроенный 3amp импульсный регулятор, 3 пользовательские кнопки, 1 динамик, 3 светодиода, кнопку сброса, определитель напряжение батареи, драйвер моторов L298 с раздельным главным и логическим входами. Особенности
- 100% arduino compatible
- 2 channel motor controller
- Servo power (VS): 0V - 14VDC
- 3A switching regulator
- Main Battery (min - max): 6V - 14VDC
- I/O Voltages (Low / High): 0.0V / 5.0V
- I/O Logic: TTL
- I/O Maximum Current: 25 mA sink, 25 mA source
- Temperature Range: -40 to +125 °C Примечание: Суммарный ток для всех выводов, не должна превышать 90 мА <<

DFRobot 3PA и AWD Rovers. Он может дать вам определять степень вращения колеса. Кодировщик использует бесконтактный метод для преобразования сигналов угл <<

Shield Описание Ethernet плата расширения W5100 Чип W5100 Комплектность Micro SD Вес брутто 46.00 Транспортная упаковка: размер/кол-во 42*28*18.5/50 <<

модули (ARDUINO) Чип ATmega328P Описание Программируемый микроконтроллер на AVRmega328P Напряжение питания, В 5 Глубина, мм 69 Вес брутто 28.50 Транспортная упаковка: размер/кол-во 52*29*28/100 Частота тактовая - 16 МГц Интерфейс 14 цифровых входов/ выходов, 6 аналоговых входов Тип разъёма USB/ DC Память ОЗУ - 1 килобайт, EEPROM - 512 байт Ширина, мм 53 Номинальный ток, мА вход/ выход - 40 Входное напряжение, В 712 (рекомендуется) <<

спроектирован специально для решения робототехнических задач. Совместимость с Arduino позволяет использовать готовые проверенные реш <<

of mbed and Arduino. With Seeeduino Arch, you can use mbed C/C++ SDK, libraries and online development tools to rapidly build a prototype. Seeeduino Arch has standard Arduino appearance and Grove connectors. It_s convenient to extend Shield and Grove products to Seeeduino Arch. Features
mbed enabled
lots of published libraries, projects
easy to use C/C++ SDK
online development tools
Stardard Arduino Appearance, two Grove connectors
available with 3.3V compatible shields
a large number of grove modules
Drag-n-drop programming
NXP LPC11U24 MCU
Low power ARM Cortex-M0 Core
48MHz, 32KB Flash, 8KB RAM, 4KB EEPROM
USB Device, 2xSPI, UART, I2C <<

этому шилду можно подключить два щеточных электромотора постоянного тока или один 4-х проводной двухфазный шаговый двигатель. Особенности:
- ARDUINO сов <<

maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that the Arduino has only a few PWM outputs, and maybe those outputs are conflicting with another shield! What now? You could give up OR you could just get our handy PWM and Servo driver shield. It's just like our popular PWM/Servo Breakout but now Arduino-ready and works with any Arduino that uses shields: Uno, Leo, Mega, ADK, its all good. When we saw this chip, we quickly realized what an excellent add-on this would be. Using only two I2C pins, control 16 free-running PWM outputs! You can even stack up 62 shields to control up to 992 PWM outputs (which we would really like to see since it would be glorious and like 4 feet tall) Because I2C is a shared bus you can also connect other I2C devices and sensors to the SCL/SDA pins as long as their addresses don't conflict (this shield has address 0x40)
There's an I2C-controlled PWM driver with a built in clock. That means that, unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running!
It is 5V compliant, which means you can control it from a 3.3V Arduino and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)
6 address select pins so you can stack up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs
Adjustable frequency PWM up to about 1.6 KHz
12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate
Configurable push-pull or open-drain output
We wrapped up this lovely chip into a shield with a couple nice extras
Terminal block for power input (or you can use the 0.1' breakouts on the side)
Reverse polarity protection on the terminal block input
Green and red power-good LEDs
3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1' so you can only stack 4 next to each other on 0.1' header
Stackable design. You'll need to pick up stacking headers and right angle 3x4 headers in order to stack on top of this shield without the servo connections getting in the way.
A spot to place a big capacitor on the V+ line (in case you need it)
220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial
Solder jumpers for the 6 address select pins
A lot of extra space remaining? Let's turn it into a prototyping area. You get a 5x20 proto area for any extra wiring you'd like to add
This product comes with a fully tested and assembled shield as well as 4 pieces of 3x4 male straight header (for servo/LED plugs), a 2-pin terminal block (for power) and a stick of 0.1' header so you can plug into an Arduino. A little light soldering will be required to assemble and customize the board by attaching the desired headers but it is a 15 minute task that even a beginner can do. If you want to use right-angle 3x4 headers, we also carry a 4 pack in the shop. Servos and Arduino not included - but we do sell tons of different servos in the shop so pick up a few while you're here! Dimensions (no headers or terminal block) 2.1' x 2.7' x 0.1' (54mm x 70mm x 3mm) <<

combines everything you love about Trinket with the familiarity of the core Arduino chip, the ATmega328. It's like an Arduino Pro Mini with more pins and USB tossed in. Trinket's a year old now, and while its been great to see tons of tiny projects, sometimes you just need more pins, more FLASH, and more RAM. That's why we designed Pro Trinket, with 18 GPIO, 2 extra analog inputs, 28K of flash, and 2K of RAM. Like the Trinket, it has onboard USB bootloading support - we opted for a MicroUSB jack this time. We also added Optiboot support, so you can either program your Pro Trinket over USB or with a FTDI cable just like the Pro Mini and friends. The Pro Trinket PCB measures only 1.5' x 0.7' x 0.2' (without headers) but packs the same capability as an Arduino UNO. So it's great once you've finished up a prototype on an official Arduino UNO and want to make the project smaller. The Pro Trinket 3V uses the Atmega328P chip, which is the same core chip in the Arduino UNO/Duemilanove/Mini/etc. However, it uses 3V logic and 12MHz clock which means it's good when you want a lower-power and lower-voltage setup. Pro Trinket is programmable using the Arduino IDE as you already set up, and 95% of Arduino projects will work out of the box! Here's some things you may have to consider when adapting Arduino sketches: Pins #2 and #7 are not available (they are exclusively for USB)
The Pro Trinket 3V runs at 12MHz, this doesn't affect most projects. Only the most timing-specific libraries may be affected, check the documentation! The NeoPixel Library works fine at 12MHz.
The onboard power supply is a 3.3V regulator and it can provide 150mA output
You cannot plug shields directly into the Pro Trinket
There is no Serial-to-USB chip onboard. This is to keep the Pro Trinket small and inexpensive, you can use any FTDI cable to connect to the FTDI port for a Serial connection. The USB connection is for uploading new code only.
The bootloader on the Pro Trinket use 4KB of FLASH so the maximum sketch size is 28,672 bytes. The bootloader does not affect RAM usage.
Here's some handy specifications: ATmega328P onboad chip in QFN package running at 3.3V logic
12MHz clock rate, 28K FLASH available
USB bootloader with a nice LED indicator looks just like a USBtinyISP so you can program it with AVRdude and/or the Arduino IDE (with a few simple config modifications).
Also has headers for an FTDI port for reprogramming
Micro-USB jack for power and/or USB uploading, you can put it in a box or tape it up and use any USB cable for when you want to reprogram.
On-board 3.3V power regulator with 150mA output capability and ultra-low dropout. Up to 16V input, reverse-polarity protection, thermal and current-limit protection.
Power with either USB or external output (such as a battery) - it'll automatically switch over
On-board green power LED and red pin #13 LED
Reset button for entering the bootloader or restarting the program.
Works with 99% of existing Arduino sketches (anything that doesn't use more than 28K, and doesn't require pins #2 and #7) Dimensions:
- Size: 38mm x 18mm x 2mm
- Height with MicroUSB: 4mm / 0.16'
- Weight: 2.6g <<

скоростью осуществляется двумя ШИМ сигналами. Направление вращения выбирается двумя цифровыми сигналами.
Характеристики:
Количество каналов: 2
Рабочее напряжение: 4.8 ...46 V(силовая часть)
Напряжение логики: 6 ... 12 V
Рабочий ток на канал: 2 A
Драйвер: L298N
Размеры: 47х53 мм
Название производителя: DF ROBOT - 2A Dual Motor Controller <<

размерах может устанавливаться практически в любом месте. Используются металлические шестерни.
Вращение / поддержка: двойной подшипник
Диапазон вращения: 180 °
Скорость: 6,0: 0,21 sec/60 ° 7.4V: 0,19 sec/60 °
Крутящий момент: 6,0: (12,00 кг / см) 7,4: (13,60 кг / см)
Вес: 70 грамм. Размеры: Длина: 40 мм
Ширина: 20 мм
Высота: 42 мм
Вес: 57 г <<

Характеристики:
Диаметр: 12mm, длина: 35,33mm.
Выходной вал: D-образный, d=3mm, длина 9,27mm.
Передаточное число: 1000:1
Скорость без загрузки: 32 о <<

W5100 ethernet chip providing a network (IP) stack capable of both TCP and UDP. The Arduino Ethernet Shield supports up to four simultaneous socket connections.
The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top.
The latest revision of the shield adds a micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino UNO and Mega (using the Ethernet library coming in Arduino 0019). An SD card library is not yet included in the standard Arduino distribution.
Arduino communicates with both the W5100 and SD card using the SPI bus (through the ICSP header). This is on digital pins 11, 12, and 13 on the Duemilanove and pins 50, 51, and 52 on the Mega. On both boards, pin 10 is used to select the W5100 and pin 4 for the SD card. These pins cannot be used for general i/o. On the Mega, the hardware SS pin, 53, is not used to select either the W5100 or the SD card, but it must be kept as an output or the SPI interface won't work.
Note that because the W5100 and SD card share the SPI bus, only one can be active at a time. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you're not using one of the peripherals in your program, however, you'll need to explicitly deselect it. To do this with the SD card, set pin 4 as an output and write a high to it. For the W5100, set digital pin 10 as a high output. The shield provides a standard RJ45 ethernet jack. <<